Technical Note: Clinical modeling and validation of breast tissue expander metallic ports in a commercial treatment planning system for proton therapy.

To validate breast tissue expander metallic port (MP) models in a commercial treatment planning system (TPS) in proton pencil beam scanning (PBS) treatments for breast cancer patients with breast tissue expanders. Three types of MPs taken out of a Mentor CPX4, a Natrelle 133, and a PMT Integra breast tissue expanders and a 650 cc saline filled Mentor CPX4 expander were placed on top of acrylic slabs, and scanned using a Siemens Somatom Definition AS Open RT CT scanner. Structure templates for each of the MPs were designed within Eclipse TPS. The CT numbers for the metallic parts were overridden to reflect measured or calculated relative proton stopping powers (RPSPs). Mock targets were contoured in acrylic to represent postmastectomy chest-wall radiation therapy (PMRT) targets. Plans with different beam incident angles were optimized using the Eclipse TPS to deliver uniform prescription dose to the target using Hitachi Probeat-V PBS beams. Eclipse calculated doses and an in-house Monte Carlo (MC) code calculated doses were compared to the measured Gafchromic EBT3 film doses in acrylic. TPS/MC and film dose comparison results showed that (1) 3%/2 mm/10% threshold Gamma pass rates were better than 90.8% in the acrylic target region for all plans; (2) comparing TPS and film doses for the individual beam plans in the MP dose shadow areas, the area with dose difference above 5% ([ΔA] 5%) ranged from 1.1 to 5.0 cm2 , and the maximum dose difference ([ΔD] 0.01 cm2 ) ranged from 12.5% to 25.0%; (3) comparing MC and film doses for the individual beam plans in the MP dose shadow areas, the (ΔA) 5% varied from 1.1 to 2.9 cm2 and (ΔD) 0.01 cm2 varied from 8.5% to 24.2%; (4) for a plan composed of three individual beams treating through the Mentor CPX4 expander, the TPS (ΔA) 5% was less than 0.13 cm2 , and the (ΔD) 0.01 cm2 was less than 6% in the MP dose shadow areas. It is feasible to treat patients with tissue expanders using multiple PBS beams using a structure template with CT number overridden to represent the measured/calculated RPSP for MPs for PBS treatment planning. MC dose was more accurate than analytical dose in the areas with high dose gradient caused by the density heterogeneity of the breast tissue expander MPs.

Kang Y ，Shen J ，Bues M ，Hu Y ，Liu W ，Ding X ... -  《-》

Outcomes of and treatment planning considerations for a hybrid technique delivering proton pencil-beam scanning radiation to women with metal-containing tissue expanders undergoing post-mastectomy radiation.

Following mastectomy, immediate breast reconstruction often involves the use of temporary tissue expanders (TEs). TEs contain metallic ports (MPs), which complicate proton pencil-beam scanning (PBS) planning. A technique was implemented for delivering PBS post-mastectomy radiation (PMRT) to patients with TEs and MPs. A protocol utilizing a hybrid single- and multi-field optimization (SFO, MFO) technique was developed. Plans were robustly optimized using a Monte Carlo algorithm. A CTV_eval structure including chest wall (CW) and regional nodal (RNI) targets and excluding the TE was evaluated. Organ at risk (OAR) dosimetry and acute toxicities were analyzed. Twenty-nine women were treated with this technique. A 2-field SFO technique was used superior and inferior to the MP, with a 3 or 4-field MFO technique used at the level of the MP. Virtual blocks were utilized so that beams did not travel through the MP. A port-to-CW distance of 1 cm was required. Patients underwent daily image-guidance to ensure the port remained within a 0.5 cm internal planning volume (ITV). Median RT dose to CTV_eval was 50.4 Gy (45.0-50.4). Median 95% CTV_eval coverage was 99.5% (95-100). Optically stimulated luminescent dosimeter (OSLD) readings were available for 8 patients and correlated to the dose measurements in the treatment planning system (TPS); median OSLD ratio was 0.99 (range, 0.93-1.02). Delivering PMRT with PBS for women with metal-containing TEs using a hybrid SFO/MFO technique is feasible, reproducible, and achieves excellent dose distributions. Specialized planning and image-guidance techniques are required to safely utilize this treatment in the clinic.

DeCesaris CM ，Mossahebi S ，Jatczak J ，Rao AD ，Zhu M ，Mishra MV ，Nichols E ... -  《-》

Modeling AeroForm tissue expander for postmastectomy radiation therapy.

The AeroForm chest wall tissue expander (TE) is a silicon shell containing a metallic CO2 reservoir, placed surgically after mastectomy. The patient uses a remote control to release compressed CO2 from the reservoir to inflate the expander. AeroForm poses challenges in a radiation therapy setting: The high density of the metallic reservoir causes imaging artifacts on the planning CT, which encumber structure definition and cause misrepresentation of density information, in turn affecting dose calculation. Additionally, convolution-based dose calculation algorithms may not be well-suited to calculate dose in and around high-density materials. In this study, a model of the AeroForm TE was created in Eclipse treatment planning system (TPS). The TPS model was validated by comparing measured to calculated transmission through the AeroForm. Transmission was measured with various geometries using radiochromic film. Dose was calculated with both Varian's Anisotropic Analytical Algorithm (AAA) and Acuros External Beam (AXB) algorithms. AAA and AXB were compared using dose profile and gamma analyses. While both algorithms modeled direct transmission well, AXB better modeled lateral scatter from the AeroForm TE. Clinical significance was evaluated using clinical data from four patients with AeroForm TEs. The AeroForm TPS model was applied, and RT plans were optimized using AAA, then re-calculated with AXB. Structures of clinical significance were defined and dose volume histogram analysis was performed. Compared to AXB, AAA overestimates dose in the AeroForm device. Changes in clinically significant regions were patient- and plan-specific. This study proposes a clinical procedure for modeling the AeroForm in a commercial TPS, and discusses the limitations of dose calculation in and around the device. An understanding of dose calculation accuracy in the vicinity of the AeroForm is critical for assessing individual plan quality, appropriateness of different planning techniques and dose calculation algorithms, and even the decision to use the AeroForm in a postmastectomy radiation therapy setting.

Dziemianowicz E ，Gardner SJ ，Chin Snyder K ，Wen N ，Walker EM ，Fraser C ，Reding A ，Chetty IJ ... -  《Journal of Applied Clinical Medical Physics》

Modeling of the metallic port in breast tissue expanders for photon radiotherapy.

The purpose of this study was to model the metallic port in breast tissue expanders and to improve the accuracy of dose calculations in a commercial photon treatment planning system (TPS). The density of the model was determined by comparing TPS calculations and ion chamber (IC) measurements. The model was further validated and compared with two widely used clinical models by using a simplified anthropomorphic phantom and thermoluminescent dosimeters (TLD) measurements. Dose perturbations and target coverage for a single postmastectomy radiotherapy (PMRT) patient were also evaluated. The dimensions of the metallic port model were determined to be 1.75 cm in diameter and 5 mm in thickness. The density of the port was adjusted to be 7.5 g/cm3 which minimized the differences between IC measurements and TPS calculations. Using the simplified anthropomorphic phantom, we found the TPS calculated point doses based on the new model were in agreement with TLD measurements within 5.0% and were more accurate than doses calculated based on the clinical models. Based on the photon treatment plans for a real patient, we found that the metallic port has a negligible dosimetric impact on chest wall, while the port introduced significant dose shadow in skin area. The current clinical port models either overestimate or underestimate the attenuation from the metallic port, and the dose perturbation depends on the plan and the model in a complex way. TPS calculations based on our model of the metallic port showed good agreement with measurements for all cases. This new model could improve the accuracy of dose calculations for PMRT patients who have temporary tissue expanders implanted during radiotherapy and could potentially reduce the risk of complications after the treatment.

Yoon J ，Xie Y ，Heins D ，Zhang R ... -  《Journal of Applied Clinical Medical Physics》

Dose perturbation caused by metallic port in breast tissue expander in proton beam therapy.

Proton beam treatment is being looked favourably now in breast treatment. Tissue expanders are often placed after mastectomy that contains metallic port for saline injection which produces dose perturbations in proton beam therapy with uncertain dosimetry. Dose perturbation for a stainless-steel injection port from a breast implant is investigated in this study. Measurements, Monte-Carlo simulation, and calculated dose distribution of plans based on kVCT and MVCT images are compared. Treatment plans are performed on kVCT and MVCT images to observe the effect of metal artifact from the breast implant. The kVCT based plan underestimates the beam range due to the overestimated water equivalent thickness of the metal ports as a result of image degradation. Compared to the measurement with metal port in the proton beam, the MVCT-based treatment planning provides more accurate dose calculation than the kVCT-based results. The dose perturbation factor calculated from MVCT planning is within 10% of the measurement results while HU corrected kVCT plan still shows dose difference as large as 100% due to the incorrect range pull back calculation caused by the misrepresentation of the volume between the plastic cap and the stainless-steel base. The dose enhancement observed at the metal and solid water interface is as large as 15%, which needs to be accounted for in the planning process if there is a clinical concern. Dose reduction as large as 16% is observed with depth from 1 cm to 4 cm underneath the thickest part of the metallic port whereas lateral dose perturbation is also seen up to 7 mm. The measurement data are supported by the Monte-Carlo simulated results with a maximum dose difference of 6%. It is concluded that if proton beam is used with metallic port, MVCT imaging data is recommended. In lieu of MVCT, DECT, CT scanner with metal artifact reduction software or in the very least, extended HU range should be used to reduce the streaking artifact as well as to produce a more accurate image of the metallic port.

Zhao L ，Moskvin VP ，Cheng CW ，Das IJ ... -  《Biomedical Physics & Engineering Express》