A formalism for traceable dosimetry in superficial electronic brachytherapy (eBT).

Objective. Despite the number of treatments performed with electronic brachytherapy (eBT) there is no uniform methodology for reference dosimetry for international traceability to primary dosimetry standards in different eBT systems. The objective of this study is to propose a formalism for traceability reference dosimetry in superficial eBT, that is easy to apply in the clinic. This method was investigated for an Elekta Esteya with one applicator.Approach. The calibration x-ray spectrum at the primary standards dosimetry laboratory was matched to the measured eBT photon spectrum. Subsequently, two ionization chambers of different types were calibrated at the primary standard dosimetry laboratory (PSDL) in terms of air kerma against a primary standard. The chambers were used to measure ionization chamber reading ratios in-air at different distances from the applicator. Monte Carlo based air kerma ratios were calculated at different positions from the eBT applicator as well as backscatter factors in water and average mass energy absorption ratios in water and in air. Relative measurements with radiochromic films were performed in a water phantom to determine the ratio of absorbed dose to water,Dw, at the surface toDwat 1 cm depth in water. These were compared with Monte Carlo calculations.Main results. Calculations and measurements were combined to estimate theDwat the surface and at 1 cm depth in water. Ionization chamber agreement of the surface dose was 1.7%, within an uncertainty of 6.8% (k= 2). They agreed with the manufacturer dosimetry within 1.8%, with an uncertainty of 5.0% (k= 2). The feasibility of the formalism and methodology for the Esteya system was demonstrated.Significance. This study proposes a method for harmonization of traceable reference dosimetry for eBT contact treatments which does not involve a detailed simulation of the ionization chamber. The method demonstrated feasibility for one eBT system using one surface applicator. In the future the method could be applied for different eBT systems.

de Prez L ，Avilés Lucas P ，Kok E 《-》

Comparison and uncertainty evaluation of different calibration protocols and ionization chambers for low-energy surface brachytherapy dosimetry.

Candela-Juan C ，Vijande J ，García-Martínez T ，Niatsetski Y ，Nauta G ，Schuurman J ，Ouhib Z ，Ballester F ，Perez-Calatayud J ... -  《-》

On the use of the absorbed depth-dose measurements in the beam calibration of a surface electronic high-dose-rate brachytherapy unit, a Monte Carlo-based study.

To evaluate the use of the absorbed depth-dose as a surrogate of the half-value layer in the calibration of a high-dose-rate electronic brachytherapy (eBT) equipment. The effect of the manufacturing tolerances and the absorbed depth-dose measurement uncertainties in the calibration process are also addressed. The eBT system Esteya® (Elekta Brachytherapy, Veenendaal, The Netherlands) has been chosen as a proof-of-concept to illustrate the feasibility of the proposed method, using its 10 mm diameter applicator. Two calibration protocols recommended by the AAPM (TG-61) and the IAEA (TRS-398) for low-energy photon beams were evaluated. The required Monte Carlo (MC) simulations were carried out using PENELOPE2014. Several MC simulations were performed modifying the flattening filter thickness and the x-ray tube potential, generating one absorbed depth-dose curve and a complete set of parameters required in the beam calibration (i.e., HVL, backscatter factor (Bw ), and mass energy-absorption coefficient ratios (µen /ρ)water,air ), for each configuration. Fits between each parameter and some absorbed dose-ratios calculated from the absorbed depth-dose curves were established. The effect of the manufacturing tolerances and the absorbed dose-ratio uncertainties over the calibration process were evaluated by propagating their values over the fitting function, comparing the overall calibration uncertainties against reference values. We proposed four scenarios of uncertainty (from 0% to 10%) in the dose-ratio determination to evaluate its effect in the calibration process. The manufacturing tolerance of the flattening filter (±0.035 mm) produces a change of 1.4% in the calculated HVL and a negligible effect over the Bw , (µen /ρ)water,air , and the overall calibration uncertainty. A potential variation of 14% of the electron energies due to manufacturing tolerances in the x-ray tube (69.5 ± ~10 keV) generates a variation of 10% in the HVL. However, this change has a negligible effect over the Bw and (µen /ρ)water,air , adding 0.1% to the overall calibration uncertainty. The fitting functions reproduce the data with an uncertainty (k = 2) below 1%, 0.5%, and 0.4% for the HVL, Bw , and (µen /ρ)water,air , respectively. The four studied absorbed dose-ratio uncertainty scenarios add, in the worst-case scenario, 0.2% to the overall uncertainty of the calibration process. This work shows the feasibility of using the absorbed depth-dose curve in the calibration of an eBT system with minimal loss of precision.

Valdes-Cortez C ，Niatsetski Y ，Ballester F ，Vijande J ，Candela-Juan C ，Perez-Calatayud J ... -  《-》

Simulation evaluation of NIST air-kerma rate calibration standard for electronic brachytherapy.

Hiatt JR ，Rivard MJ ，Hughes HG 《-》

Investigations on the beam quality correction factor for ionization chambers in high-energy brachytherapy dosimetry.

Objective. To enhance the investigations on MC calculated beam quality correction factors of thimble ionization chambers from high-energy brachytherapy sources and to develop reliable reference conditions in source and detector setups in water.Approach. The response of five different ionization chambers from PTW-Freiburg and Standard Imaging was investigated for irradiation by a high dose rate Ir-192 Flexisource in water. For a setup in a Beamscan water phantom, Monte Carlo simulations were performed to calculate correction factors for the chamber readings. After exact positioning of source and detector the absorbed dose rate at the TG-43 reference point at one centimeter nominal distance from the source was measured using these factors and compared to the specification of the calibration certificate. The Monte Carlo calculations were performed using the restricted cema formalism to gain further insight into the chamber response. Calculations were performed for the sensitive volume of the chambers, determined by the methods currently used in investigations of dosimetry in magnetic fields.Main results. Measured dose rates and values from the calibration certificate agreed within the combined uncertainty (k= 2) for all chambers except for one case in which the full air cavity was simulated. The chambers showed a distinct directional dependence. With the restricted cema formalism calculations it was possible to examine volume averaging and energy dependence of the perturbation factors contributing to the beam quality correction factor also differential in energy.Significance. This work determined beam quality correction factors to measure the absorbed dose rate from a brachytherapy source in terms of absorbed dose to water for a variety of ionization chambers. For the accurate dosimetry of brachytherapy sources with ionization chambers it is advisable to use correction factors based on the sensitive volume of the chambers and to take account for the directional dependence of chamber response.

Failing T ，Hensley FW ，Keil B ，Zink K ... -  《-》