Impact of pre-coagulation on the ceramic membrane process during oil-water emulsion separation: Fouling behavior and mechanism.

Coagulation has been evaluated as an economical and effective pre-treatment method for controlling membrane fouling. We investigated the influence of the pre-coagulation of oil-water (O/W) emulsions on the formation of membrane fouling in the ceramic membrane process. The results confirmed that pre-coagulation effectively mitigated the fouling formation on the ceramic membrane surface during the O/W emulsion separation. The mechanism of mitigating membrane fouling by pre-coagulation was proposed, owing to the reduction in the zeta potential value of oil droplets by pre-coagulation, resulting in weak electrostatic attraction between oil droplets and ceramic membrane surfaces, and an increase in the size of the oil droplets by pre-coagulation, leading the formation of a cake layer fouling. In addition, the decrease in the hydrophobicity of oil droplets by pre-coagulation resulted in alleviating the hydrophobic interaction between oil droplets and membrane surface. The proposed fouling mechanism was supported by the characterization of the virgin and fouled membrane surfaces and the analysis of the fouling resistance ability of the membranes. Our study could be indicative of mitigation protocols that can be used to alleviate membrane fouling on ceramic membranes during oily wastewater treatment.

Jang D ，Lee J ，Jang A 《-》

Ceramic membrane fouling during ultrafiltration of oil/water emulsions: roles played by stabilization surfactants of oil droplets.

Lu D ，Zhang T ，Ma J 《-》

Oil-in-water emulsion separation: Fouling of alumina membranes with and without a silicon carbide deposition in constant flux filtration mode.

Ceramic membranes have drawn increasing attention in oily wastewater treatment as an alternative to their traditional polymeric counterparts, yet persistent membrane fouling is still one of the largest challenges. Particularly, little is known about ceramic membrane fouling by oil-in-water (O/W) emulsions in constant flux filtration modes. In this study, the effects of emulsion chemistry (surfactant concentration, pH, salinity and Ca2+) and operation parameters (permeate flux and filtration time) were comparatively evaluated for alumina and silicon carbide (SiC) deposited ceramic membranes, with different physicochemical surface properties. The original membranes were made of 100% alumina, while the same membranes were also deposited with a SiC layer to change the surface charge and hydrophilicity. The SiC-deposited membrane showed a lower reversible and irreversible fouling when permeate flux was below 110 L m-2 h-1. In addition, it exhibited a higher permeance recovery after physical and chemical cleaning, as compared to the alumina membranes. Increasing sodium dodecyl sulfate (SDS) concentration in the feed decreased the fouling of both membranes, but to a higher extent in the alumina membranes. The fouling of both membranes could be reduced with increasing the pH of the emulsion due to the enhanced electrostatic repulsion between oil droplets and membrane surface. Because of the screening of surface charge in a high salinity solution (100 mM NaCl), only a small difference in irreversible fouling was observed for alumina and SiC-deposited membranes under these conditions. The presence of Ca2+ in the emulsion led to high irreversible fouling of both membranes, because of the compression of diffusion double layer and the interactions between Ca2+ and SDS. The low fouling tendency and/or high cleaning efficiency of the SiC-deposited membranes indicated their potential for oily wastewater treatment.

Chen M ，Heijman SGJ ，Luiten-Olieman MWJ ，Rietveld LC ... -  《-》

Robust zirconia ceramic membrane with exceptional performance for purifying nano-emulsion oily wastewater.

While membrane-based oil-water separation has been widely explored, using conventional membranes to treat oily wastewaters remains practically challenging especially when such wastewaters contain more stable nano-sized oil droplets and are of high oil content, and harsh chemical conditions. Herein, we report a novel protocol of efficiently separating both synthetic and real oil nano-emulsions via specially designed robust zirconia membranes. The best-performing zirconia membrane, fabricated at low sintering temperature, has relatively uniform sub-100 nm pores and is underwater superoleophobic. Such zirconia membranes possess not only outstanding separation performance under long-term operation but robust structural stability at harsh conditions. At different cross-flow velocities, a combined model of intermediate pore blocking and cake filtration dominated membrane fouling behavior. Specifically, at high pH value (especially > pH(IEP)), membrane fouling was effectively mitigated due to a dominant role of electrostatic repulsion interaction at membrane-oil interface. Compared with conventional and commercial ceramic membranes, our zirconia membrane is the first reported in literature that can effectively reject nano-sized oil droplets (∼18 nm) with over 99% rejection. Moreover, the zirconia membrane has also been challenged with real degreasing wastewater with very high oil content (∼4284 mg L-1) and pH (∼12.4) and delivered consistently high separation performance over many operation cycles.

Wang X ，Sun K ，Zhang G ，Yang F ，Lin S ，Dong Y ... -  《-》

Fouling mitigation and cleanability of TiO(2) photocatalyst-modified PVDF membranes during ultrafiltration of model oily wastewater with different salt contents.

Kovács I ，Veréb G ，Kertész S ，Hodúr C ，László Z ... -  《-》