Successive Multiple Ionic-Polymer Layer Coatings for Intact Protein Analysis by Capillary Zone Electrophoresis-Mass Spectrometry: Application to Hemoglobin Analysis.

Adsorption of analytes, e.g., proteins, often interfere with separation in CE, due to the relatively large surface of the narrow capillary. Coatings often are applied to prevent adsorption and to determine the electroosmotic flow (EOF), which is of major importance for the separation in CE. Successive multiple ionic-polymer layer (SMIL) coatings are frequently used for protein analysis in capillary electrophoresis resulting in high separation efficiency and repeatability. Here, the coating procedure of a five-layer SMIL coating is described using quaternized diethylaminoethyl dextran (DEAEDq) as polycation and poly(methacrylic acid) (PMA) as polyanion. Depending on the analyte, different polyions may be used to increase separation efficiency. However, the coating procedure remains the same.To demonstrate the applicability of SMIL coatings in CE-MS, human hemoglobin was measured in a BGE containing 2 M acetic acid. DEAEDq-PMA coating was found to be the most suitable for hemoglobin analysis due to relatively low reversed electroosmotic mobility leading to increased electrophoretic resolution of closely related proteoforms. Thereby, not only alpha and beta subunit of the hemoglobin could be separated, but also positional isoforms of glycated and carbamylated species were separated within 24 min.

Salzer L ，Stolz A ，Dhellemmes L ，Höchsmann A ，Leclercq L ，Cottet H ，Neusüß C ... -  《-》

Modulation of the electroosmotic mobility using polyelectrolyte multilayer coatings for protein analysis by capillary electrophoresis.

Successive multiple ionic-polymer layers (SMIL) coatings have been often used in capillary electrophoresis due to their simplicity to implement and regenerate. However, the performances of the separation are strongly dependent on the nature of the polyelectrolyte partners used to build the SMIL coating. In this work, we investigate new couples of polyelectrolytes that were not tested before: namely, polybrene (PB), quaternized diethylaminoethyl dextran (DEAEDq) and ε-poly(lysine) (ε-PLL), as polycations, in combination with poly(acrylic acid), dextran sulfate, poly(styrenesulfonate), poly(methacrylic acid) and poly(l-lysine citramide), as polyanions. Systematic study of intra- and inter-capillaries repeatabilities/reproducibilities was performed based on the determination of migration time, separation efficiency and electroosmotic mobility. Interestingly, the electroosmotic flow was found to vary with the nature of the polycation on a broad range of electroosmotic mobility decreasing in magnitude in the order of PB>ε-PLL > DEAEDq, whatever the polyanion associated. Application of the coatings to the separation of proteins is illustrated in a 0.5 M acetic acid BGE, including CE-MS separation of ribonuclease B-glycoforms of the same mass (positional or structural isomers).

Leclercq L ，Morvan M ，Koch J ，Neusüß C ，Cottet H ... -  《-》

Advanced portrayal of SMIL coating by allying CZE performance with in-capillary topographic and charge-related surface characterization.

A successive multiple ionic polymer layer (SMIL) coating composed of four layers improved the capillary electrophoretic separation of a recombinant major birch pollen allergen and closely related variants when poly(acrylamide-co-2-acrylamido-2-methyl-1-propansulfonate) (55% PAMAMPS) replaced dextran sulfate as terminal SMIL layer. 55% PAMAMPS decelerated the electroosmotic flow (EOF) due to its lower charge density. Atomic force microscopy (AFM) was used to investigate SMIL properties directly on the inner capillary surface and to relate them to EOF measurements and results of associated CZE separations of a mixture of model proteins and peptides that were performed in the same capillary. For the first time, AFM-based biosensing topography and recognition imaging mode (TREC) under liquid conditions was applied for a sequential characterization of the inner surface of a SMIL coated capillary after selected treatments including pristine SMIL, SMIL after contact with the model mixture, after alkaline rinsing, and the replenishment of the terminal polyelectrolyte layer. A cantilever with tip-tethered avidin was used to determine the charge homogeneity of the SMIL surface in the TREC mode. SMIL coated rectangular capillaries with 100 μm internal diameter assured accessibility of the inner surface for this cantilever type. Observed changes in CZE performance and EOF mobility during capillary treatment were also reflected by alterations in surface roughness and charge distribution of the SMIL coating. A renewal of the terminal SMIL layer restored the original surface properties of SMIL and the separation performance. The alliance of the novel TREC approach and CZE results allows for an improved understanding and a comprehensive insight in effects occurring on capillary coatings.

Stock LG ，Leitner M ，Traxler L ，Bonazza K ，Leclercq L ，Cottet H ，Friedbacher G ，Ebner A ，Stutz H ... -  《-》

Modifying last layer in polyelectrolyte multilayer coatings for capillary electrophoresis of proteins.

Protein adsorption on the inner wall of the fused silica capillary wall is an important concern for capillary electrophoresis (CE) analysis since it is mainly responsible for separation efficiency reduction. Successive Multiple Ionic-polymer Layers (SMIL) are used as capillary coatings to limit protein adsorption, but even low residual adsorption strongly impacts the separation efficiency, especially at high separation voltages. In this work, the influence of the chemical nature and the PEGylation of the polyelectrolyte deposited in the last layer of the SMIL coating was investigated on the separation performances of a mixture of four model intact proteins (myoglobin (Myo), trypsin inhibitor (TI), ribonuclease a (RNAse A) and lysozyme (Lyz)). Poly(allylamine hydrochloride) (PAH), polyethyleneimine (PEI), ε-poly(L-lysine) (εPLL) and α-poly(L-lysine) (αPLL) were compared before and after chemical modification with polyethyleneglycol (PEG) of different chain lengths. The experimental results obtained by performing electrophoretic separations at different separation voltages allowed determining the residual retention factor of the proteins onto the capillary wall via the determination of the plate height at different solute velocities and demonstrated a strong impact of the polycationic last layer on the electroosmotic mobility, the separation efficiency and the overall resolution. Properties of SMIL coatings were also characterized by quartz microbalance and atomic force microscopy, demonstrating a glassy structure of the films.

Roca S ，Leclercq L ，Gonzalez P ，Dhellemmes L ，Boiteau L ，Rydzek G ，Cottet H ... -  《-》

Covalent cationic copolymer coatings allowing tunable electroosmotic flow for optimization of capillary electrophoretic separations.

Electroosmotic flow (EOF) plays a pivotal role in optimization of capillary electrophoresis (CE) separations of (bio)molecules and (bio)particles. EOF velocity is directly related to analysis time, peak resolution and separation efficiency. Here, we report a concept of charged polymer coatings of the inner fused silica capillary wall, which allows anodic EOF with mobility ranging from 0 to ∼(30-40) × 10-9 m2V-1s-1. The capillary wall is modified by covalently bound cationic copolymer poly(acrylamide-co-(3-acrylamidopropyl)trimethylammonium chloride) (PAMAPTAC) containing variable ratio of the charged monomer in the 0-60 mol. % interval. The EOF mobility showed minor variability with composition of background electrolyte (BGE) and pH in the 2-10 interval. The coatings were evaluated by CE-UV and nanospray CE-MS in the counter-EOF arrangement for a series of basic drug molecules in acetic acid based acidic BGE. Tunable EOF velocity was demonstrated as a useful tool for optimization of peak resolution, separation efficiency and migration time of analytes. Electrostatic repulsion of positively charged capillary surface was shown as beneficial for suppression of analyte adsorption, notably for hydrophobic cationic analytes.

Konášová R ，Butnariu M ，Šolínová V ，Kašička V ，Koval D ... -  《-》