Development of a novel methodology for QA of respiratory-gated and VMAT beam delivery using Octavius 4D phantom.

The objective of this study was to develop and evaluate a series of quality assurance (QA) techniques based on Octavius 4D phantom for testing of respiratory-gated treatment delivery, integrity of dose rate vs gantry speed in volumetric-modulated arc therapy (VMAT) commissioning, and multileaf collimator (MLC) positioning accuracy of a linear accelerator. An Octavius 4D phantom capable of rotating with the gantry and recording the detector signal with a sampling rate of 10 Hz was isocentrally set up and an inclinometer was also installed to measure the gantry angle simultaneously. A simple arc test was created and delivered with gating function activated to measure the timing accuracy of the gating window. A tailor-made dose rate vs gantry speed plan was also designed to test the accuracy of measured dose rate, gantry speed, and actual control points. All experiments were conducted while machine log files were collected for comparison. The variations of beam flatness, symmetry, and field size were analyzed as a function of gantry angle to evaluate the influence from the modulation of dose rate and gantry speed. MLC position accuracy was evaluated based on specific garden fence plans. The time of gating window was measured to be less than 10-millisecond deviation from the log data. Gantry backlash was observed and quantified to be 1.72° with an extra stabilization time of 1.16 seconds for a gating arc with gantry speed of 6°/s. In the dose rate vs gantry speed test, the mean deviation between measured gantry angle and log data was less than 0.2° after a time delay of 0.25 second was corrected. The measured dose rate agreed with the log data very well with a mean deviation of 0.05%, and even the transit of modulation was tracked successfully. There was a statistically significant difference on the variation of beam parameters between a VMAT plan and a simple arc plan. The induced MLC position errors were detected with an accuracy of 0.05 mm. The leaf position reproducibility was found to be better than 0.02 mm, whereas the routine MLC position accuracy was better than 0.1 mm. A time-resolved method using Octavius 4D phantom has been developed and proven to be convenient for respiratory gating QA, dose rate vs gantry speed test, and MLC QA. Gating time, dose rate, and gantry speed-induced leave position error could be directly measured with high accuracy after comparison with the machine log data. This study also highlights the capability of the phantom in quantifying the variation of flatness, symmetry, and field size during gantry rotation.

Yang B ，Geng H ，Ding Y ，Kong CW ，Cheung CW ，Chiu TL ，Lam WW ，Cheung KY ，Yu SK ... -  《-》

Commissioning and quality assurance for VMAT delivery systems: An efficient time-resolved system using real-time EPID imaging.

An ideal commissioning and quality assurance (QA) program for Volumetric Modulated Arc Therapy (VMAT) delivery systems should assess the performance of each individual dynamic component as a function of gantry angle. Procedures within such a program should also be time-efficient, independent of the delivery system and be sensitive to all types of errors. The purpose of this work is to develop a system for automated time-resolved commissioning and QA of VMAT control systems which meets these criteria. The procedures developed within this work rely solely on images obtained, using an electronic portal imaging device (EPID) without the presence of a phantom. During the delivery of specially designed VMAT test plans, EPID frames were acquired at 9.5 Hz, using a frame grabber. The set of test plans was developed to individually assess the performance of the dose delivery and multileaf collimator (MLC) control systems under varying levels of delivery complexities. An in-house software tool was developed to automatically extract features from the EPID images and evaluate the following characteristics as a function of gantry angle: dose delivery accuracy, dose rate constancy, beam profile constancy, gantry speed constancy, dynamic MLC positioning accuracy, MLC speed and acceleration constancy, and synchronization between gantry angle, MLC positioning and dose rate. Machine log files were also acquired during each delivery and subsequently compared to information extracted from EPID image frames. The largest difference between measured and planned dose at any gantry angle was 0.8% which correlated with rapid changes in dose rate and gantry speed. For all other test plans, the dose delivered was within 0.25% of the planned dose for all gantry angles. Profile constancy was not found to vary with gantry angle for tests where gantry speed and dose rate were constant, however, for tests with varying dose rate and gantry speed, segments with lower dose rate and higher gantry speed exhibited less profile stability. MLC positional accuracy was not observed to be dependent on the degree of interdigitation. MLC speed was measured for each individual leaf and slower leaf speeds were shown to be compensated for by lower dose rates. The test procedures were found to be sensitive to 1 mm systematic MLC errors, 1 mm random MLC errors, 0.4 mm MLC gap errors and synchronization errors between the MLC, dose rate and gantry angle controls systems of 1°. In general, parameters measured by both EPID and log files agreed with the plan, however, a greater average departure from the plan was evidenced by the EPID measurements. QA test plans and analysis methods have been developed to assess the performance of each dynamic component of VMAT deliveries individually and as a function of gantry angle. This methodology relies solely on time-resolved EPID imaging without the presence of a phantom and has been shown to be sensitive to a range of delivery errors. The procedures developed in this work are both comprehensive and time-efficient and can be used for streamlined commissioning and QA of VMAT delivery systems.

Zwan BJ ，Barnes MP ，Hindmarsh J ，Lim SB ，Lovelock DM ，Fuangrod T ，O'Connor DJ ，Keall PJ ，Greer PB ... -  《-》

A novel method for routine quality assurance of volumetric-modulated arc therapy.

Wang Q ，Dai J ，Zhang K 《-》

[Multileaf Collimator Position Accuracy of Respiratory Gated VMAT].

Kanai K ，Kotabe K ，Kijima K ，Ishikawa Y ，Nakayama H ... -  《-》

Correlation of phantom-based and log file patient-specific QA with complexity scores for VMAT.

Agnew CE ，Irvine DM ，McGarry CK 《Journal of Applied Clinical Medical Physics》