Assessment of the Biomechanical Performance of 5 Plating Techniques in Fixation of Mandibular Subcondylar Fracture Using Finite Element Analysis.

The aim of this study was to compare the performances of 5 plating techniques for fixation of unilateral mandibular subcondylar fracture. Five titanium plating techniques for fixation of condylar fracture were analyzed using the finite element method. The modeled techniques were 1) 1 straight plate, 2) 2 parallel straight plates, 3) 2 angulated straight plates, 4) 1 trapezoidal plate, and 5) 1 square plate. Three-dimensional models were generated using patient-specific geometry for the mandible obtained from a computerized tomographic image of a healthy living man. Plates were designed and combined with the mandible and analyzed under a 500-N load. The single straight plate presented the most inferior performance; it presented maximum displacement and strain on cortical bone. The trapezoidal plate induced the least amount of strain on cortical bone and was best at resisting displacement. The trapezoidal plate is recommended for fixation of subcondylar fracture.

Darwich MA ，Albogha MH ，Abdelmajeed A ，Darwich K ... -  《-》

Comparison of Neck Screw and Conventional Fixation Techniques in Mandibular Condyle Fractures Using 3-Dimensional Finite Element Analysis.

To compare the mechanical stress on the mandibular condyle after the reduction and fixation of mandibular condylar fractures using the neck screw and 2 other conventional techniques according to 3-dimensional finite element analysis. A 3-dimensional finite element model of a mandible was created and graphically simulated on a computer screen. The model was fixed with 3 different techniques: a 2.0-mm plate with 4 screws, 2 plates (1 1.5-mm plate and 1 2.0-mm plate) with 4 screws, and a neck screw. Loads were applied that simulated muscular action, with restrictions of the upper movements of the mandible, differentiation of the cortical and medullary bone, and the virtual "folds" of the plates and screws so that they could adjust to the condylar surface. Afterward, the data were exported for graphic visualization of the results and quantitative analysis was performed. The 2-plate technique exhibited better stability in regard to displacement of fractures, deformity of the synthesis materials, and minimum and maximum tension values. The results with the neck screw were satisfactory and were similar to those found when a miniplate was used. Although the study shows that 2 isolated plates yielded better results compared with the other groups using other fixation systems and methods, the neck screw could be an option for condylar fracture reduction.

Conci RA ，Tomazi FH ，Noritomi PY ，da Silva JV ，Fritscher GG ，Heitz C ... -  《-》

Finite element analysis of three patterns of internal fixation of fractures of the mandibular condyle.

The most stable pattern of internal fixation for fractures of the mandibular condyle is a matter for ongoing discussion. In this study we investigated the stability of three commonly used patterns of plate fixation, and constructed finite element models of a simulated mandibular condylar fracture. The completed models were heterogeneous in the distribution of bony material properties, contained about 1.2 million elements, and incorporated simulated jaw-adducting musculature. Models were run assuming linear elasticity and isotropic material properties for bone. This model was considerably larger and more complex than previous finite element models that have been used to analyse the biomechanical behaviour of differing plating techniques. The use of two parallel 2.0 titanium miniplates gave a more stable configuration with lower mean element stresses and displacements over the use of a single miniplate. In addition, a parallel orientation of two miniplates resulted in lower stresses and displacements than did the use of two miniplates in an offset pattern. The use of two parallel titanium plates resulted in a superior biomechanical result as defined by mean element stresses and relative movement between the fractured fragments in these finite element models.

Aquilina P ，Chamoli U ，Parr WC ，Clausen PD ，Wroe S ... -  《-》

A 3-dimensional finite-element analysis investigating the biomechanical behavior of the mandible and plate osteosynthesis in cases of fractures of the condylar process.

Wagner A ，Krach W ，Schicho K ，Undt G ，Ploder O ，Ewers R ... -  《oral surgery oral medicine oral pathology oral radiology and endodontics》

Comparative finite element analysis of the biomechanical stability of 2.0 fixation plates in atrophic mandibular fractures.

The objective of the present study was to conduct a computational, laboratory-based comparison of the biomechanical stability of 2.0 fixation locking plates with different profiles in Class III atrophic mandibular fractures using 3-dimensional finite element analysis. Three-dimensional finite element models simulating Class III atrophic mandibular fractures were constructed. The models were divided into 4 groups according to plate thickness (1.0, 1.5, 2.0, and 2.5 mm). Fractures were simulated in left mandibular bodies, and 3 locking screws were used on each side of each fracture for fixation. Bite forces of approximately 63 N were simulated in the incisor and molar regions of the mandibles in finite element models. The level of compressive strain on the bone around the screw was within the physiological limit. No significant difference was observed in the displacement of bone segments in the fracture region. Von Mises stress was higher during simulated bites in the molar region for plates with thicknesses of 1.0 mm. Plate tension values were below the level required for permanent deformation or fracture in all models. The 2.5-mm-thick plate presented better biomechanical performance than all other plates. The 2.0-mm-thick plate also showed satisfactory results and adequate safety limits. Large-profile (2.0-mm-thick) locking plates showed better biomechanical performance than did 1.0- and 1.5-mm-thick plates and can be considered an alternative reconstruction plate for the treatment of Class III atrophic mandibular fractures.

Vajgel A ，Camargo IB ，Willmersdorf RB ，de Melo TM ，Laureano Filho JR ，Vasconcellos RJ ... -  《-》