Hot melt extrusion (HME) for amorphous solid dispersions: predictive tools for processing and impact of drug-polymer interactions on supersaturation.

The processing parameters for HME have been evaluated and the impact of solid state intermolecular drug-polymer interactions on supersaturation has been investigated. Poorly water soluble drugs Indomethacin (IND), Itraconazole (ITZ), and Griseofulvin (GSF) and hydrophilic polymers - Eudragit EPO, Eudragit L-100-55, Eudragit L-100, HPMCAS-LF, HPMCAS-MF, Pharmacoat 603, and Kollidon VA-64 were selected for this study. Solubility parameters calculations (SPCs), differential scanning calorimetry (DSC), and rheological analysis of drug-polymer physical mixtures (PMs) was performed. The solid dispersions were manufactured using HME and characterized by powder X-ray diffraction (PXRD), polarized light microscopy (PLM), Fourier transform infra-red (FTIR) Spectroscopy, and dissolution study. Results obtained by DSC correlated well with SPC, showing single glass transition temperatures for all the PMs except ITZ in Eudragit EPO that depicted the highest difference in solubility parameters. The zero rate viscosity (η₀) was dependent on the melting point and consequently the state of the drug in the polymer at the softening temperature. The η₀ of PMs was useful to estimate the processing conditions for HME and to produce transparent glassy HMEs from most of the PMs. The amorphous conversion due to HME was confirmed by PXRD and PLM. The solid state drug-polymer interactions occurred during HME could be confirmed by FTIR analysis. Highest supersaturation could be achieved for IND, ITZ, and GSF using Eudragit EPO, HPMCAS-LF, and Eudragit L-100-55, respectively where relatively higher stretching of the carbonyl peaks was observed by FTIR. Thus, the highest dissolution rate and supersaturation of poorly water soluble drugs could be attributed to drug-polymer interactions occurred during HME.

Sarode AL ，Sandhu H ，Shah N ，Malick W ，Zia H ... -  《-》

Hot melt extrusion for amorphous solid dispersions: temperature and moisture activated drug-polymer interactions for enhanced stability.

Sarode AL ，Sandhu H ，Shah N ，Malick W ，Zia H ... -  《-》

A New Extrudable Form of Hypromellose: AFFINISOL™ HPMC HME.

Huang S ，O'Donnell KP ，Keen JM ，Rickard MA ，McGinity JW ，Williams RO 3rd ... -  《AAPS PHARMSCITECH》

Application of film-casting technique to investigate drug-polymer miscibility in solid dispersion and hot-melt extrudate.

Determination of drug-polymer miscibility is critical for successful development of solid dispersions. This report details a practical method to predict miscibility and physical stability of drug with various polymers in solid dispersion and, especially, in melt extrudates by applying a film-casting technique. Mixtures of itraconazole (ITZ) with hydroxypropylmethylcellulose phthalate (HPMCP), Kollidon(®) VA 64, Eudragit(®) E PO, and Soluplus(®) were film-casted, exposed to 40°C/75% RH for 1 month and then analyzed using differential scanning calorimetry (DSC), powder X-ray diffractometry, and polarized light microscopy (PLM). ITZ had the highest miscibility with HPMCP, being miscible at drug to polymer ratio of 6:4 (w/w). There was a downward trend of lower miscibility with Soluplus(®) (miscible at 3:7, w/w, and a few microcrystals present at 4:6, w/w), Kollidon(®) VA 64 (2:8, w/w) and Eudragit(®) E PO (<1:9, w/w). PLM was found more sensitive to detect drug crystallization than DSC and powder X-ray diffractometry. There was general correlation between results of film casting and hot-melt extrusion (HME) using a twin screw extruder. For ITZ-Soluplus(®) mixtures, HME at 4:6 (w/w) resulted in a single phase, whereas drug crystallization was observed at higher drug load. HME of ITZ-Kollidon(®) VA 64 mixtures also correlated well with the miscibility predicted by film casting.

Parikh T ，Gupta SS ，Meena AK ，Vitez I ，Mahajan N ，Serajuddin AT ... -  《-》

Characterization of physico-mechanical properties of indomethacin and polymers to assess their suitability for hot-melt extrusion processs as a means to manufacture solid dispersion/solution.

Chokshi RJ ，Sandhu HK ，Iyer RM ，Shah NH ，Malick AW ，Zia H ... -  《-》